Skip to main content

Filter By:

Park Tool

$49.95 - $86.95
Frame and Fork Taps will become a lifesaver at some time for virtually every mechanic. These taps are made of high-carbon steel and are precision ground. Park Tool Frame and Fork Taps cut easily and fit conventional tap handles.
$50.95
The BBT-30.4 Bottom Bracket Bearing Tool Set is designed and built to install and remove the bearings used in BB30, PressFit 30 (PF30), 386EVO, BBright and PF121 bottom bracket systems. The BBT-30.4 features a bushing set used in conjunction with a head cup press to quickly and precisely press the BB30 and PF30 bearings in the bottom bracket shell. The included BB30 bearing remover works from inside the shell to easily push out bearings.
$50.95
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Portable Wheel Dishing Tool is a must. It disassembles quickly for storage or travel and allows you to easily check centering on road, mountain and BMX wheels from 24 to 29 inches in diameter and it works with any hub. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
$50.95
Accurately gauge the straightness of disc brake rotors while the wheel is mounted in a TS-2.2 or TS-2 Professional Wheel Truing Stand (each sold separately). Park Tool's Rotor Truing Gauge features an infinitely adjustable, finely threaded indicator gauge. It works with any diameter brake rotor.
$52.95
Park's Threadless Star Nut Setter makes it quick and easy to install star-fangled nuts used with 1-inch and 1-1/8-inch threadless headset systems. Using a durable steel driver and built-in guide, the TNS-4 perfectly aligns the star-fangled nut and sets it to the proper depth every time. Plus, the unique design virtually eliminates pinched fingers!
$54.95
The HBH-3 securely holds handlebars in place on any bike in any position while in a repair stand. It's useful for brake bleeding, cable and housing routing, lever adjustment, or any scenario where you want to prevent the handlebars from rotating, including storage or working with the bike rotated upwards. With its articulating clamps and adjustable straps, the HBH-3 can easily be attached in a wide variety of positions onto almost any handlebar, seatpost, frame, fork, or repair stand. Anodized aluminum construction with soft rubber straps. - Straps install onto any round tube from 12mm to 60mm (0.5" to 2.4"), as well as most irregular and aero-shaped tubing found on bicycles - Rotating articulating clamps allow for secure installation onto virtually any bicycle in a wide range of positions - Usable extension length of 18" to 32" (45cm to 81cm) - Collapses and folds to 17" (43cm) for storage
$54.95
Clean out or restore damaged threads in crank arms with Park Tool's Pedal Taps. They're sold as a set of right and left hand threads. Made of high carbon steel, precision ground, and hardened to stay sharp, they cut easily and fit all conventional tap handles. • Includes a set of 2 taps, 9/16" x 20 tpi • Made of high carbon steel, precision ground, and hardened to stay sharp • Fits all conventional tap handles The tap drill size for a 9/16-inch x 20 tpi thread is nominally 33/64-inch.
$55.95
Many bicycles will not shift or track properly because the front and rear wheels are not in line with the frame. If these conditions still exist after wheel and derailleur adjustments, the seat stays, chain stays, and rear drop outs of the frame may be misaligned. For years the accepted method to check the alignment of the rear drop-out was to run a string on either side. This method does work to some extent. However, it is not accurate because the measurement is not taken at the drop-out. With the Park Tool Frame Alignment Gauge, the alignment can be checked quickly and accurately at the drop-out. It includes a retractable pointer to fit all sizes and types of bicycles.
$55.95
Park's Threadless-Fork Saw Guide ensures a straight, accurate cut on threadless forks. Slide on the guide, clamp it down and the hardened-steel cutting slot ensures a perfect cut every time. You can remove as little as 1mm, too.
$56.95
Suspension maintenance and tuning require tools designed for a precise fit. The SKT-6 from Park Tools is a shop-quality set of six flat-faced sockets designed for use with common suspension fork fittings. Ideal for use with Park Tool Torque Wrenches, the 3/8-inch drive sockets are forged from tough chrome vanadium steel and chrome plated for lasting durability. - 24, 26, 27, 28, 30, 32mm flat-faced sockets - All sockets are 3/8" drive - Note: 27mm socket is tapered for better access on Suntour suspension forks
$56.95
Park Tool's Bottom Bracket Bearing Tool Set removes and installs (with a bearing press which is sold separately) BB86, BB90, BB92 and Press Fit bottom brackets from Shimano, Race Face, SRAM and others that use a nominal 24mm-diameter spindle. This tool has a bearing remover that fits inside the bottom bracket shell and into the bearing so the bearings can be tapped out of the frame with a hammer. The set also includes two bushings that you use in conjunction with a bearing press for precision bearing installation (bearing press sold separately).
$59.95
The Park Tool SBS-1.2 is a shop-quality set of sockets, hex bits, and Torx style bits, selected specifically for common bike repair needs. Ideal for use with Park Tool torque wrenches, the SBS-1.2 3/8" drive bits and sockets are made from tough, chrome vanadium steel for lasting durability.
$59.95
Truing stand upright extensions install in seconds on any TS-2 or TS-2.2 Truing Stand, allowing the stand to be used on wheels with hubs up to 200mm wide (tandem, fat and downhill bikes), as well as on wheels with a 29-inch mountain bike tire installed*. In addition, specially sized bosses serve as adaptors so the stand can be used with wheels using thru-axle hubs with removable axles. Same features as the the TS-2EXT.2 with the addition of slots to secure rear drive e-bike wheels. * Note: TS-2.2 Truing Stand does not require these adaptors to accommodate 29-inch wheels but does require it to fit hub widths from 180mm to 200+mm.
$59.95
Park's Threadless-Fork Saw Guide ensures a straight, accurate cut on threadless carbon forks. Specially designed to accommodate wider, carbon specific saw blades, the SG-8 ensures a perfect cut every time. Slide on the guide, clamp it down and the specially shaped hardened-steel cutting slot guides your saw blade. And, the SG-8 Saw Guide ensures a straight, clean cut on fork steerer tubes up to 1-1/4-inches.
$61.95
The 1729-TA Sliding Thru Axle Adaptor is designed to allow any Park Tool PRS-20, PRS-21 or PRS-23 Repair Stand to accept 12mm and 15mm thru axle wheeled bikes.
$61.95
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Wheel Alignment Gauge (also called a dishing tool) is a must. It allows you to easily check centering on road, mountain and BMX wheels from 16 to 29 inches in diameter. It works with any hub width and its innovative design even allows it to be accurately used with the tire still on the wheel. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
$62.95
Commonly referred to as a 4th Hand, Park's Cable Stretcher pulls cables tight. Its one-hand operation and thumblock holds the cable so you can easily maintain cable tension while tightening cable fixing bolts and nuts. Made from chrome-plated and heat-treated steel and featuring cushion grips for comfort, the Park Cable Stretcher is a must for any serious mechanic.
$63.66
Park Tool's TS-RK is a complete rebuild kit for the TS-2 truing stand. It is complete with the most commonly replaced small parts and the instructions needed to get your stand back into top working condition. In addition to making the stand more accurate and reliable, once installed, the new parts also allow the stand to be readjusted much more easily, should it be thrown out of adjustment. This is a great addition to the older TS-2 stands. If your stand has silver-colored shaft collars, upgrade with the TS-RK. The TS-RK includes the following: • 1 - #211S Main Shaft • 4 - #749-1 Bearing Washer • 2 - #748-1 Needle Bearing • 2 - #209-2 Shaft Adjusting Collar • 1 - #229 Spring • 4 - #232-2 Split Nylon Bushing • 2 - #235-2 Split Nylon Bushing • 1 - #222-SR Right Caliper Spring • 1 - #222-SL Left Caliper Spring • 1 - Set of Installation and Adjustment Instructions
$63.95
Securely holds the TS-4 Professional Wheel Truing Stand and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
$63.95
Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4 was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Stand Mount mounts to any Park Tool Professional Shop Stand (all versions of PRS-2, -3, -4, and -33) - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)
$64.95
The QTH-1 is an ergonomic T-handled bit driver equipped with eight common bits to fit a wide variety of fasteners and fittings found on bicycles. The magnetic "quick-change" handle allows for one-handed operation and makes changing bits quick and easy. The bit holder can be magnetically attached to any magnetic surface such as a repair stand or tool box, or can be permanently mounted to any wall or tool board. The QTH-1 is a professional-grade tool built to withstand the rigors of daily shop use and is fully rebuildable. Includes the following magnetic 1/4" bits: - 2mm, 2.5mm, 3mm, 4mm, 5mm & 6mm hex - T25 Torx-compatible - #2 Philips cross tip - Bit holder includes empty spaces for 2 extra bits
$65.95
Securely holds any of Park's TS-2, TS-2.2, and TS-2.2P Professional Wheel Truing Stands and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
$65.95
Securely holds the TS-4.2 Professional Wheel Truing Stand and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
$70.95
The DC-2 is a vernier caliper for accurately measuring seat posts, head tubes, bearings, spoke diameters, and other components, featuring a large LCD screen for accuracy and ease of use. The tool’s ability to measure in metric and inches in external, internal, depth, and stepped dimensions make it an indispensable shop tool. - Range: 150 mm | 6" - Resolution: 0.01 mm | 0.0005" - Accuracy: +/- 0.02 mm | 0.001" - Repeatability: +/- 0.01 mm | 0.0005" - Measures external, internal, depth, and stepped dimensions - Uses LR44 batteries
$71.95
Shop-quality, adjustable torque driver that limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The ATD-1.2 features all-metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at Park Tool's factory in Minnesota.
$72.95
"Take the guesswork out of internal routing. The IR-1.3 speeds the installation of internally-routed cable, housing, electronic wiring and hydraulic hose into carbon fiber, titanium, and aluminum frames. The straightforward guide magnet system utilizes five long guide cables with unique fittings, which can be routed through the frame in a number of ways using the included guide magnet. Everything is neatly stored in a convenient compact case. A true time and frustration saver!??Includes five 188 cm (74"") guide cables with attached magnets and unique fittings: • Barbed adapter — Threads into the end of brake & shift cable housing as well as hydraulic brake hose • Rubber adapter — Securely holds electronic shifting wire such as Shimano® Di2, SRAM® RED® eTAP®, FSA® K-Force® WE®, and Campagnolo® EPS • Di2®-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® shift wire, and is perfectly sized to fit into frame holes as small as 6 mm • Di2® EW-SD300-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® EW-SD300 shift wire • Reverse-polarity magnet — Used in conjunction with any of the other guide cables - feeds into the opposite end and meets the leading cable in the middle, aiding in routing on frames with tricky interior shapes Also included: • Double-threaded barb — Securely attaches new housing or hydraulic hose to existing housing or hose, allowing for easy replacement without redoing the routing • Guide magnet — routes guide cables through the frame from the outside"
$74.95
Park Tool's Thru Axle Adaptors make it possible to adapt all Park Tool Truing Stands to work with 12mm, 15mm, 20mm, and 25mm thru axle front wheels, as well as Cannondale Lefty wheels (each sold separately). The TS-TA also work with the rear 135mm thru axle hubs in the TS-2.2 and TS-3. The TS-TA when used in the TS-8, TS-25, TS-15, TS-7 or TS-5 will work with all rear thru axle hubs. For thru axle hubs greater than 135 (142, 150, 157, etc.) in the TS-2.2, use the TS-2TA Thru Axle Adaptors (sold separately).
$74.95
Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4T was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Bench Top Mount sits firmly on any flat surface - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)
$76.95
Park's Tire Seating Tool is designed to quickly seat the bead on stubborn tires. During inflation some tire beads can slip below the rim edge and become difficult to pull out and align. The PTS-1 comes to the rescue with its non-slip jaws and vinyl-coated handles that provide plenty of leverage for pulling out the tire. Plus, it's adjustable to fit various tire widths.
$84.95
The DAG-2.2 is an indispensable shop tool that can be used to both measure and straighten misaligned derailleur hangers solving a high percentage of shifting problems. - Gauge bar made of heavy gauge, chrome plated steel - Adjusts to fit 20" to 29"+ wheels - Replaceable threaded tip - Upgraded large inner shaft for added strength* - Tighter tolerances for improved accuracy* - Improved clearance and reach to fit more frame/hanger combos including low clearance thru-axle derailleur hangers* *Compared to DAG-2
Page 1 of 2 Next page